• Image 1
Model #: 860-817
Quantity:

Product Description

Certain Glock Adjustable Kensight Sight Adjustable with Beveled Blade

Developed specifically for the Glock pistols, with their fixed sight dovetail placed at the extreme rear of the slide. Ours is a clean-sheet design, not just a recycled sight from our parts bin. Knowledgeable shooters will note that our rear sight blade matches evenly with the rear of the slide on the Glock pistol, not like other sights which extend 1/4" past the slide, making it easy to catch on clothing and gear. Suitable for Glock Models 17, 22, 31, 34, 35 and 37. *REQUIRES A .315"-.350" FRONT SIGHT*

Shadow Image

Warranty Information

Limited Lifetime Warranty

We stand behind our products. All Kensight Sights are covered by a limited lifetime warranty. We guarantee our products against defects in material and construction. This limited lifetime warranty does not extend to normal signs of wear. It does not cover breakage, damage or rust due to misuse, improper maintenance, accidents, loss or theft. The warranty does not extend to damages cause by unauthorized repairs.

Any product we determine to be defective will be repaired or replaced solely at our discretion. To receive warranty repair or replacement, the owner must send the product to be evaluated by KFS Industries Warranty Services located at our Atlanta, Georgia headquarters. In addition to the provisions of this warranty, the owner may also have other rights that can vary by state. No other warranties are implied or expressed other than what is specifically stated here.

Warranty Service

All products returned to KFS Industries for a warranty claim must have prior approval of a KFS Customer Service employee in the form of a Return Material Authorization Number (RMA). The RMA must be displayed on the exterior of the return carton. Merchandise returned without an RMA will be refused. The RMA number assigned will expire 30 days from date of issue. To obtain an RMA, please call the KFS Atlanta, Georgia headquarters at (404) 691-7611.

After you obtain your RMA, Please send your product to:

KFS Industries Inc.
875 Wharton Dr SW
Atlanta, GA 30336
 

You must pay the shipping and insurance costs to return your product to KFS Industries Inc., and we will pay the shipping charges to return the product to your US address only. All International shipping will be the responsibility of the consumer.

Upon receipt of a returned product, we will verify warranty coverage. If the product is not covered by warranty, KFS Industries Inc. will send you an estimate of the cost to repair your product prior to performing any services not covered.

Shadow Image

Product Reviews

Write Review

  1. Great sights except way oversized

    Posted by Damian DeNatale on 7th Mar 2017

    These sights were unusually oversized. It took my gunsmith over an hour to trim off metal from the dovetail and the underside of the sights. I expect that for 1911's but thought that the sights for the Glock would be closer.
    That aside, the sights are great and reasonably priced.

    Kensight: All our dovetails are oversized, because different manufactures have different depths for their dovetail tolerances. If we go with the exact correct dovetail size, the tolerances may allow the sight to slip through. We also have to consider tool wear, so no dovetail is exactly the same. Oversized dovetails may take longer to install, but the end result is a factory fit ready to serve you for years into the future.

  2. Best of the best

    Posted by steve weldon on 27th May 2016

    Back in the 90's I owned my own custom 1911 shop and did good business. Back then everyone wanted steel guns and everyone wanted to carry a work of art. Bomar sights were requested and recommended more than any other. 20+ years later (time I spent living in Asia) everyone wants polymer guns and sights don't seem to mater much. And what happened to Bomar sights? Frustrated. And then I found Ken Sights and they made them for my new polymer Glock. I order a set and the steel and quality seems the same or better than Bomar's from the past. Installation took some time but the finished product is great. Couldn't be more happy.

  3. Tight and Tall

    Posted by Kensight Customer on 25th Mar 2016

    Like the sight, just like the bo-mars I had in the G24 but don't hang off the back. Took a lot of filling to fit in the new G34. Have to get an over 0.360" front sight for my minor loads to hit low enough without bottoming out the rear sight.

  4. Great tall sight

    Posted by alex pocs on 30th Jul 2015

    Great sight, fitted well into factory dovetail with minor filing. Uses. 315 highfront sight. I put a trijicon by ameriglo on front. Holstered gun, never suspecting the blued surfaces on the sides of the sight blade would rust by the next day. Applied kroil and was OK. Never have I had to worry about rust on my Glock 22. Kensight...please apply a rust free surface treatment to your Glock Sights. PS...I have the Novak style undercut kensight on my custom Springfield loaded 1911 I use for 3 gun comp and I never have seen rust on that one. Great sight....minor annoyance.

    REPLY: We will look into this issue for you.

  5. First Class

    Posted by Brett on 11th Jul 2014

    Great design and machining.

Shadow Image